Main page » Rekord D / Commodore B » Engine / Clutch

Engine / Clutch

Gasket for fuel pump from new production, fits to all CIH-engines 1,5 - 3,0 WITH bakelit-flange.
Price is for one piece.

9,95 EUR

incl. 19% tax excl. Shipping costs

Gasket Oil Filler Cap

Rubberkork Gasket on oil filler cap, from new production, fits to all models.
Price is for one piece.

1,65 EUR

incl. 19% tax excl. Shipping costs

Gasket Oil Pump Cover CIH

Gasket Oel Pump Cover all CIH

3,50 EUR

incl. 19% tax excl. Shipping costs

Gasket Set for Engine lower CIH 1,5 - 2,2

Gasket set for lower engine / crankcase gasket set in very good accessory quality, suitable for the following models:
- Kadett B 1.5 - 1.9
- Kadett C 1.6 - 2.0
- Rekord B 1.5 - 1.9
- Rekord C 1.5 - 1.9
- Rekord D 1.7 - 2.0 + 2.1D
- Rekord E 1.7 - 2.2 + 2.3TD
- Manta / Ascona A 1.6 - 1.9
- Manta / Ascona B 1.6 - 2.4
- Monza / Senator A 2.0 + 2.2 + 2.3TD
- GT 1900
Price per set for one engine.
A different stop screw for the camshaft may have to be used on early models.

44,95 EUR

incl. 19% tax excl. Shipping costs

Gasket Set for Engine lower CIH 1,5 - 2,2, Reinz

Gasket set for lower engine / crankcase gasket set in original equipment quality from Victor Reinz, suitable for the following models:
- Kadett B 1.5 - 1.9
- Kadett C 1.6 - 2.0
- Rekord B 1.5 - 1.9
- Rekord C 1.5 - 1.9
- Rekord D 1.7 - 2.0 + 2.1D
- Rekord E 1.7 - 2.2 + 2.3TD
- Manta / Ascona A 1.6 - 1.9
- Manta / Ascona B 1.6 - 2.4
- Monza / Senator A 2.0 + 2.2 + 2.3TD
- GT 1900
Price per set for one engine

79,95 EUR

incl. 19% tax excl. Shipping costs

Gasket Set for Engine complete 1,7 + 1,9, 1972 up

Complete Gasket set for Engine 1,7 + 1,9 later version with screws in timing housing, 1972 up.
Can be used in the following models:
- Rekord D 1700 + 1900
- Rekord E 1700 + 1900
- Kadett C 1900
- Ascona/Manta A 1900 later 01-1972 with screws in timing housing
, Ascona / Manta B 1900
- Kadett B 1700 + 1900 later 01-1972 with screws in timing housing
Price is for one set

125,60 EUR

incl. 19% tax excl. Shipping costs

Gasket Set for Oil Pan CIH 1,5 - 2,2

Gasket Set for Oil Pan for CIH-engines 1,5 + 1,6 + 1,7 + 1,9 + 2,0 + 2,2, new production

12,95 EUR

incl. 19% tax excl. Shipping costs

Gasket Set for Oil Pan CIH-6

Gasket Set for Oil Pan for 6-Cylinder CIH-engines 2,5 + 2,8 + 3,0 . Original German Quality from Elring

14,90 EUR

incl. 19% tax excl. Shipping costs

Gasket Thermostat-Housing CIH

Gasket for thermostat housing to Cylinderhead for CIH 1,5 - 2,8 with Carburator-Engine and two screws .
Price is for one piece .

2,00 EUR

incl. 19% tax excl. Shipping costs

Gasket Thermostat-Housing CIH THREE screws

Gasket for thermostat housing to Cylinderhead for CIH 1,5 - 2,8 with Carburator-Engine and three screws .
Price is for one piece .

2,00 EUR

incl. 19% tax excl. Shipping costs

Gasket-Set Cam Shaft Cover Plates CIH-4

3-piece set of gaskets for the camshaft covers from new production ,suitable for all 4-cylinder CIH engines.
- Rekord B 1,5 - 1,9
- Rekord C 1,5 - 1,9
- Rekord D 1,7 - 2,0
- Rekord E 1,7 - 2,2
- Ascona / Manta A 1.6 - 1.9
- Ascona / Manta B 1,6 - 2,4
- Kadett B 1,5 - 1,9
- Kadett C 1,6 - 2,0
Price per 3-piece set as shown.

8,95 EUR

incl. 19% tax excl. Shipping costs

Gasket-Set Cam Shaft Cover Plates CIH-6

Gasket-set cam shaft cover plates from new production , fits to all CIH-engines 6-Cylinder 2,2 - 3,0.
Price is for a 4-parts-set

12,90 EUR

incl. 19% tax excl. Shipping costs

Gaskets Timing Housing CIH

Pair of paper gaskets for all CIH engines 1,5 - 3,0 .
Produced like original in Elring Abil 0,8mm .
Price is for one pair

6,90 EUR

incl. 19% tax excl. Shipping costs

Ground Strap for Engine to Chassis long

Ground Strap from engine to chassis, total length 325mm. Price is for one piece.

13,95 EUR

incl. 19% tax excl. Shipping costs

Ground Strap for Engine to Chassis short

Ground Strap from engine to chassis, total length 220mm. Price is for one piece.

10,95 EUR

incl. 19% tax excl. Shipping costs

High Performance Fan Blade CIH

High Performance fan blade for all CIH-engine with Standard-water-pump , does NOT fit to models with Visco . Price is for one piece

37,90 EUR

incl. 19% tax excl. Shipping costs

Hydraulic Tappet CIH 1,5 - 3,0

High quality Hydraulic Tappet for alle CIH 1,5 - 3,0 engines.
Price is for one piece.
We sell these tappets since 2008 and sold a few thousand pieces.
Complaint quote 0,14%...
We have them without any problems in several own cars.
Please let the adjustment work be done in a specialist workshop !!!
We do not offer tappets from Ajusa !!

16,95 EUR

incl. 19% tax excl. Shipping costs

Inlet valve Guide CIH 1965 up

Inlet Valve in standard size , fits to Kapitän/Admiral A 2,8 , K.A.D B 2,8S + H up to engine 50000 , 2,8E up to 30000 , Commdoore A 2,8H up to 14052 , Commodore A 2,5 all models ! 1,7N up to enginge-No. 212681 , 1,7S up to 570958 , 1,9S up to 731509 , 1,9SH up to 12968 , 1,6S up to 230805 , 1,6N up to 26200 .
Price is for one piece , only while stock last

11,90 EUR

incl. 19% tax excl. Shipping costs

Pieces:

Nut for Rocker CIH

SOLD OUT ; PROBABLY AVAILABLE AGAIN END OF APRIL !!!!

Nut for Rocker to adjust the Valve position from newest 2020-production, fits to all CIH-Engines 1,5 - 3,0.
This hiqh-quality rocker-nuts with wrench-size 15 can be used in:
- Rekord B/C/D/E 1,5/1,7/1,9/2,0/2,2
- Kadett B/C 1,5/1,6/1,7/1,9/2,0
- Manta A/B 1,6/1,9/2,0/2,2
- Ascona A/B 1,6/1,9/2,0
- Commodore A/B/C 2,5/2,8
- Kapitaen/Admiral/Diplomat A/B 2,8
- Senator/Monza A 2,0/2,2/2,5/2,8/3,0 (not C30SE)
Price is for one piece.

6,95 EUR

incl. 19% tax

Oil Dip Stick Guide Tube CIH "Special"

This special dipstick guide tube fits CIH motors with rear sump.
The tube mounts in the 13mm hole in the block to guide the dipstick into the deep end of the oil pan keeping it away from the crankshaft.
It also fits on the outside of the Aluminum oil pans where the dipstick comes out near the starter motor.
The tube allows easier access to the dipstick due to the tight area near the starter.
Price is for one piece.

14,95 EUR

incl. 19% tax excl. Shipping costs

Oil Filter all models OHV + CIH 1,0 - 2,2

Fits to all models 1,0 / 1,1 / 1,2 OHV and 1,5 / 1,6 / 1,7 / 1,9, 2,0 / 2,2 CIH Rekord B/C/D/E Ascona / Manta A/B, Kadett A/B/C Monza 2,0

3,95 EUR

incl. 19% tax excl. Shipping costs

Oil Pressure Switch 1,0 - 3,0

Oil Pressure Switch, fits to all models Rekord BCDE, Kadett ABC, Commodore ABC, K.A.D. A 2,8, K.A.D. B 2,8, Manta AB, Ascona AB, Monza/Senator A. NOT for models with extra armatures!

9,00 EUR

incl. 19% tax excl. Shipping costs

Oil Pressure Switch for Extra Instruments

Oil pressure switch with 2 connections from new production, thread M14x1,5mm * , for vehicles with additional instruments:

Suitable for the following models:

- Kadett B 1,1 - 1,9, with threaded connection M14x1,5mm
- Kadett C 1,0 - 2,0E, with threaded connection M14x1,5mm
- Rekord B 1,5 - 1,9 , with threaded connection M14x1,5mm
- Rekord C 1,5 - 2,2,with threaded connection M14x1,5mm
- Rekord D 1,7 - 2,0 with threaded connection M14x1,5mm
- Rekord E 1,7 - 2,2 with threaded connection M14x1,5mm
- Commodore 2,5 - 2,8, with threaded connection M14x1,5mm
- Commodore B 2,5 + 2,8, with threaded connection M14x1,5mm
- Commodore C 2,5, with thread-connection M14x1,5mm
- Ascona / Manta A 1,6 - 1,9, with thread-connection M14x1,5mm
- Ascona / Manta B 1,6 - 2,4, with threaded connection M14x1,5mm
- Kapitaen-Admiral A ONLY 2,8, with thread-connection M14x1,5mm
- Kapitaen-Admiral-Diplomat B 2,8, with threaded connection M14x1,5mm
- Monza A 2,0 - 3,0, with threaded connection M14x1,5mm
- Senator A 2,0 - 3,0, with threaded connection M14x1,5mm
Price per piece
* if you are not sure, please check the existing thread in the engine block BEFORE buying.

69,95 EUR

incl. 19% tax excl. Shipping costs

Oil seal Crankshaft Rear CIH 1,5 - 2,0

´Made-in-Germany- Oil Seal for crankshaft rear ,tits to all CIH-engines 1,5 - 3,0 .See list of cars in tab .
Price is for one piece .

20,00 EUR

incl. 19% tax excl. Shipping costs

Oil Seal for Valve Shaft 1,5 - 2,8

Oel Seal on Valve Shaft

0,60 EUR

incl. 19% tax excl. Shipping costs

Oil Seal Steering Housing CIH

Oil seal for steering housing / crankshaft front from new production from Reinz. Fits to all CIH-engine 1,5 - 3,0.
Price is for one piece.

12,00 EUR

incl. 19% tax excl. Shipping costs

Oil-Filter 6-Cylinder 2,5 - 3,0

Oil-Filter for the 6-Cylinder-Models 2,5 / 2,8 / 3,0 CIH Commodore A/B/C, K.A.D A/B , Monza / Senator A! Price is for one piece!

11,95 EUR

incl. 19% tax excl. Shipping costs

Outlet valve Guide CIH 1965 up

Guide for exhaust valve, suitable for all CIH engines 1.5 - 3.0 from 1965-1984.
Dimensions: 12.75x9.0x67mm.
Price per piece

11,90 EUR

incl. 19% tax excl. Shipping costs

Pieces:

Pair of Screws Cylinder-Head to Steering Housing

Pair of Screws from Cylinder-Head into steering housing , for all engines 1,7 - 3,0 later chassis-No. (later 1972) . Price is for one pair

2,95 EUR

incl. 19% tax excl. Shipping costs

Piston Commodore A + B 2,5

Original piston, suitable for the following models
Commodore A 2.5S up tu engine no. 25S76768
- Commodore A 2.5H up to engine no. 25H-24334
- Commodore B 2.5
Piston diameter: 86.98mm
Code number: 8
Price per piece incl. rings and bolts as shown, only while stock last

178,50 EUR

incl. 19% tax excl. Shipping costs

Piston Ring Set 1,9 CIH (Standard)

Piston ring set ( standard iussue ) for one piston 1,9 CIH , fits to Kadett B+C , Rekord C+D+E , Ascona / Manta A+B , Olympia A.
Price is for one setas pictured for one piston.
Please ask for oversize rings

22,95 EUR

incl. 19% tax excl. Shipping costs

Piston Ring Set 2,0 CIH (Standard)

Piston ring set (standard issue) 2,0 CIH, fits to Kadett C , Rekord D+E , Ascona / Manta B , Senator / Monza A.
Price is for one set for one piston.
Please ask for oversize rings

35,70 EUR

incl. 19% tax excl. Shipping costs

Show 65 to 96 (from a total of 123 products)